How to Use Your Wet-Stop®2 Alarm
Pre-use Test: Pull out the tabs under battery lid to activate the device. Ensure the volume switch setting is set
to the highest level. Next, depress the white sensor pushbutton (Figure 2). Insert a wet cloth fully inside the
sensor grip. Make sure the metal probes inside the sensor (Figure 2) are in contact with the wet cloth
(Figure 3). The alarm is working if it sounds.
Alarm Tone and Volume Selection: Next select the alarm tone by moving the tone selection switch to
different positions and choosing your desired tone while continuing to grip the wet cloth with the sensor.
After the tone selection step is complete, move the volume switch to the off position to stop the alarm. You
can then set the volume switch to the desired level before attaching the Wet-Stop2 to the child’s clothing as
described in the section below (Wet-Stop2 Use). Note: Parent should set the volume when listening to the
device at an equivalent distance to the ear as the child will experience.
Warning: Do not hold an alarming device within 3 inches of the ear.
Wet-Stop®2 Use: Attach the alarm unit to the pajama top using the magnetic tether strap (Figure 4). An optional attachment method is to attach the alarm unit to pajama top using a safety pin through the hole on the top of the tether strap. Next, put the cord under the pajama or nightshirt, going in at the collar and out at the nightshirt hem (Figure 4). Attach the sensor to the child’s underwear, stretching the underwear into the sensor opening as shown in (Figure 3). A small amount of moisture on the underwear material inside the sensor opening will cause the alarm to sound, so be sure your child does not wet on the underwear before going to bed. When urine sets off the alarm, turning the volume switch to the off position will stop the sound. If the alarm is left in the on position, it will keep sounding continuously for one minute, followed by another minute
of intermittent alarm sound, followed by blinking lights.
Battery Replacement and Disposal: Palco Labs has supplied an extra set of batteries for your convenience. To replace the old batteries, use a small flat head screwdriver. Remove battery cover on the back side of the alarm unit. Insert the screwdriver in the slot on the side of the battery housing (Figure 5) and gently push the old battery out. Do not try to pry the battery holder up when removing old batteries. Insert the new battery by pushing it into the battery housing (Figure 6). Make sure the replacement batteries are positioned in the device with positive poles facing up as shown in (Figure 6). Replace only with button type CR-1620. The batteries may be purchased at most stores where batteries are sold. Dispose of the batteries only in accordance with the
manufacturer’s recommendations and local environmental regulations. For further details on local regulations, contact your local disposal or environmental agency. Should you wish to dispose of your Wet-Stop2 after use, remove the batteries and dispose of the batteries as instructed above. The Wet-Stop2 device may be disposed of with standard non-hazardous waste products.
Caution Statements:
1- The Wet-Stop2 is not intended to be used as an infant training aid for ‘potty training’ or for incontinencerelated issues. The Wet-Stop2 should not be used for children under four years of age, unless recommended by a physician.
2- As the device is being installed and during usage, ensure that the cord does not become tangled around the user in any way.
3- To prevent choking hazard, ensure the device or any of its associated components are not put in the mouth at any time.
4- If the user chooses to attach the alarm unit using a safety pin, ensure that the alarm unit is attached to the clothing as described in the section called Wet-Stop2 Use. Choose a secure pin that does not come loose easily.
5- After the pre-use test, set the volume and tone of the alarm to the most desirable selection for the user.
6- Your child may become disoriented by the sound of the alarm. A soft rug at the bedside will help prevent injury should your child roll out of bed upon awakening. Minimizing the elevation of the bed above the floor is advisable. 7- Wet-Stop2 is not intended for multiple users.
8- Store in a cool dry place between uses. Maintenance and Cleaning:
Aside from occasional battery replacement, your new Wet-Stop2 is designed for minimal maintenance. After each use rinse the sensor and wipe off the alarm if required. Make sure the alarm unit is not rinsed or submerged in water or other liquids.
Warranty:
Wet-Stop2 carries a one-year warranty against manufacturer’s defects in materials and workmanship and against breakage or failure under normal use. This warranty does not cover misuse or abuse. Palco Labs will, at its option, repair or replace this product at no charge. This warranty gives you specific legal rights, and you may also have other rights under law. For alarms not purchased directly from Palco Labs, a proof of purchase, such as the canceled check or dated store receipt must be sent along with the Wet-Stop2 to be eligible for the replacement or refund. Shipping and handling costs incurred by the customer are not reimbursable. Palco Labs reserves the right to change specifications without prior notice.
|
